All posts by Brooklyn Appliance Repair Man

Sub Zero Refrigerator Repair Troubleshooting 101 in Brooklyn NY

To keep foods at the correct temperature, most household freezers run at zero degrees. Special deep freezers run much colder, with typical temperatures ranges significantly below this point. Commercial freezers and special lab freezers commonly maintain temperatures below -20 degrees Fahrenheit. When sub zero refrigerator repairs are necessary, there are special considerations in Brooklyn, NY.

Keep Doors And Lids Firmly Closed To Prevent Loss

As soon as people notice a problem with their freezers, it is important that heat is not allowed to enter the unit. Keeping the lids or doors firmly closed lets the frozen goods packed into the space maintain the temperature for a longer period of time. Contact Bear Appliance Repair for Refrigerator Repair in Brooklyn, NY immediately. In many cases, we will be able to complete the repair on the spot. If there will be a delay due to ordering necessary parts, you’ll have the time to find an alternate storage facility to reduce loss.

Do Simple Maintenance To Reduce Equipment Failure

You have a very simple tool in your arsenal when it comes to protecting your refrigerators and freezers from failing: the vacuum cleaner. In order to work efficiently, it is vital that air intakes and air output exchange be clear of thick dust deposits. Since dust is drawn to the point of air entry, you run the risk of burning out the motor unless you regularly vacuum. Large units should be cleaned weekly, while smaller units used in the home should be cleaned monthly to avoid unnecessary sub zero refrigerator service calls.

Our Recommended Appliance Repair Company

We understand the Brooklyn area and have been providing suggestions for fast, reliable, and affordable sub zero refrigerator repair Brooklyn services for many years. Our satisfied customers know that we arrive on time and are able to diagnose the problem right away due to our years of experience in the field. Because we are an independent company, we have built our credibility and are able to complete warranty repairs on all major brands. No matter what type of unit you own, Bear Appliance Repair in Brooklyn, NY can complete the repair.

During the warm weather months when humidity levels are higher, people have more problems with their freezers and refrigerators. Our service personnel will work with you to help you keep your units running efficiently throughout the long summer months. Because we are local, we respond quickly to help you get back on track after an equipment failure.

The Best Dryer Repair in Brooklyn, NY

The Best Dryer Repair in Brooklyn NY

A clothes dryer is an essential household appliance in most of the homes in Brooklyn, New York. It helps to remove moisture from loads of clothing and other materials, as soon as, they are washed and cleaned using a washing machine. Most of today’s dryers consist of a tumbler which is a rotating drum that circulates heated air to remove moisture from the load of clothing. Regular usage of these appliances could cause minor or major breakdowns, which would require a qualified service provider to attend to the machine. This article will discuss the services of Bear Appliance Repair in Brooklyn, NY a qualified and experienced service provider for dryer repairs.

Dryer repair requests in New York are growing with each day as consumers find it more affordable than buying a new dryer. In today’s tight economic circumstances, it is always wise to use your dryer for the longest period possible. Timely maintenance and attending to small repairs immediately would no doubt enhance the lifespan of your dryer. But this will only be possible if you employ the services of a dryer repair service provider who has highly skilled and factory trained technicians.

Bear Appliance Repair is such a company that employees only highly qualified and well experienced technicians to work on your dryers. They are factory trained to maintain and repair all the major types of models and brands in the market today. Technicians  are licensed and fully insured to attend to any dryer repair job as per the requirement of the client. They have been employed by our company for the past decade and we guarantee the trustworthiness and reliability of our employees.

Most people assume that we might charge a hefty fee for our quality repair services. But our customers know that our prices are quite affordable for the quality service we offer. Even though our prices are affordable and competitive in the market, we never compromise our quality under any circumstances. We even have a mobile service unit ready to attend to any of your repair problems even in the middle of the night. Bear Appliance Repair is available 24/7 and 365 days a year.

Call them immediately, and we will send one of our qualified technicians to inspect your dryer and recommend the future course of action in repairing the dryer immediately.

How to Repair Self Cleaning Ovens and Oven Timers in Brooklyn, NY

If your oven takes too long to heat up, bake doesn’t work or if you have any other problem, simply call an oven repair specialist and let them fix the problem and return your oven to perfect working order. Call today to schedule an appointment for your oven repair in Brooklyn, NY. They will work with you to set up a repair appointment for a time that is most convenient for you.

When scheduling a Brooklyn oven repair appointment, they will always accommodate your busy life style.


The thermal element of a typical bellows-type thermostat of a bulb and a metal diaphragm connected by a capillary tube is a sealed system filled with a liquid (or sometimes gaseous). The sensing bulb is located in the oven at a point determined by the manufacturer. As the bulb is heated, the liquid or gas throughout thermal element system expands, causing an increase in pressure on the diaphragm or bellows. This actuates a switch through a mechanical linkage that provides snap-action, necessary to reduce arcing of con facts. Self-cleaning gas ranges normally use the same control as the electric ranges, with electrical solenoids opening and closing gas valves. In standard gas ranges with mechanical thermostats, the movement of the diaphragm would move a valve disk towards the seat (in the closed position). It’s easy to see that the placement of the capillary has a direct effect upon oven temperature. Be sure that it is firmly in place in the clips or brackets provided. A tube touching an oven liner gives erratic readings and sluggish operation. Sharp bends in capillary tubing can prevent transmission of pressure change to the diaphragm. To calibrate the oven thermostat, follow the same general procedures that you would for a standard oven but be certain that you turn the bake calibration screw and not the clean adjusting screw. Remove the knob from the front panel and locate the calibration adjusting screw .for the bake cycle. If it’s not readily apparent, look within the center of the control shaft or look for a movable skirt on the knob itself. You’ll probably see an arrow marked increase and pointing in a clockwise or counterclockwise direction, indicating the direction you should turn to increase or decrease temperature. Proceed to adjust the temperature following the same general guidelines given for standard ovens in the preceding chapter.

Remember, that some self-cleaning oven controls have separate calibration adjustments for the clean temperature. This requires special measuring devices and techniques, and should be left to a technician. It would be a rare occasion when a simple bake temperature calibration didn’t resolve a temperature problem. These control circuitry in various selections bring manually set by the user. The wring diagram is necessary to circuits involved. It might be helpful to know [hat I’ve observed selector switch often is blamed for many ills in self-cleaning ovens, but it seldom out to be the real culprit.


These are basically the same as standard oven timers with addition of one or two sets of contacts. A clock mechanism mechanically  activates the switches, depending upon the setting prescribed by the user. These contacts are often exposed, making visual inspection. Again, the timer is seldom the offender. On some models it disconnects a rear surface unit during clean cycles. Self-cleaning ovens are fitted with a latching device to lock the door when temperatures rise above 600 degrees. This latch keeps the door locked until the oven has cooled down after cleaning. It’s a safety device. You should never override or disconnect it. But sometimes the latch may not close completely, and an electrical interlock prevents the range from going to clean temperatures unless the door is secured. Or worse, perhaps the door won’t unlock at all. Before you remedy the problem, you must determine if the latch is mechanical (with a lever that you move manually to lock the door) or electrical (locks automatically when switch is turned to clean position).

Common Problems with Dishwashers and How to Solve Them

If your dishwasher door don’t close properly, water doesn’t drain all the way, or if you have any other problem, simply call a dishwasher repair specialist and let them fix the problem and return your dishwasher to perfect working order. Call them today to schedule an appointment for your dishwasher repair in Brooklyn. We will work with you to set up a repair appointment for a time that is most convenient for you:

When scheduling a repair appointment, we always accommodate your busy life style.

The information we provide on our website is here to help you gain more knowledge about your dishwasher. More efficient dishwasher usage can help you save on your utility bills and on possible future repairs by extending the life of your dishwasher.
Warning: DISHWASHERS CAN BECOME DANGEROUS IF YOU TRY TO REPAIR WITHOUT EXPERIENCE, TRADE KNOWLEDGE, AND THE RIGHT TOOLS. We strongly advise you not perform any dishwasher repairs on your own. Dishwasher repairs attempted by anyone without professional experience, training, and understanding of gas and electrical systems can become very dangerous. For professional help call a dishwasher repair technician.


Your dishwasher doesn’t drain the water
Cause: Dishwasher drain hose kinked or clogged
Easy dishwasher repair solution: Look for bends and straighten them. If the dishwasher hose won’t stay straight, buy a helical spring which is a bit larger than the outer diameter of the dishwasher hose and place it around the hose to keep it straight. If the hose is straight, disconnect and blow through it to see that it is clear.
Cause: Dishwasher timer sticks in “Wash” phase
Easy dishwasher repair solution: If the dishwasher timer doesn’t advance from the “Wash” to the “Drain” phase, the timer is defective and should be replaced.

Your dishwasher detergent-cup lid fails to spring open
Cause: Dish or utensil is blocking the dishwasher lid
Easy dishwasher repair solution: Make sure dishes and utensils are positioned so they can’t possibly jam against the dishwasher detergent-cup lid.
Cause: Detergent put into a wet cup or left in the cup too long
Easy dishwasher repair solution: The cup should be dry when the dishwasher detergent is put into it, because the detergent will harden in a wet cup and may cause the lid to jam. If the dishwasher detergent remains in the cup for too long a period, it may cake.
Cause: Hard-water deposits (calcium) are hampering lid operation
Easy dishwasher repair solution: Clean the dishwasher cup and lid with vinegar.
Cause:Dishwasher detergent-cup lid solenoid valve is defective
Easy dishwasher repair solution: Consult the dishwasher wiring diagram and locate the solenoid. Place a continuity tester across the dishwasher solenoid

Your dishwasher doesn’t dry the dishes
Cause: Improper placement
Easy dishwasher repair solution: Air space should be left around the dishes to permit free passage of heat.
Cause: Calcium deposits have built up on dishwasher heating element
Easy dishwasher repair solution: Examine the element and clean off deposits with vinegar.
Cause: A wire has come loose from the dishwasher heating element
Easy dishwasher repair solution: Be sure wires are tightly attached.
Cause: Heating element has burned out
Easy dishwasher repair solution: Test the dishwasher element for continuity by placing a tester across its terminals. If there is continuity, the dishwasher element has failed. Replace it.

Dishwasher mechanical components are usually mounted directly to the tub it’s important that you know how to troubleshoot the dishwasher motor, look at the bell housing on the dishwasher motor and determine if it has a manual-reset protector. No hum or noise at all?

Check for voltage at the dishwasher motor terminals with a volt-ohm meter (VOM). A relatively loud hum (less than four seconds) followed by the overload protector kicking out indicates that both running and starting windings are being energized; check for foreign object or impeller, or stuck dishwasher motor bearings. If it hums or buzzes for a longer period, chances are that the run Winding only is being energized, check the motor centrifugal switch. Problems in this area require removal and dis-assembly of the dishwasher motor. It’s best to let a dishwashers motor-repair shop replace the switch; it must be fabricated to fit the motor. The impeller itself is critical. Chips and breaks on the leading edge because erratic sprays patterns and greatly reduce washing efficiency. Damage to impellers is caused by foreign objects, primarily silverware, dropping into the sump.

If confronted with thin problem, inspect the silverware basket and be certain the machine is being loaded according to instructions.  The shaded-pole motor that powers the pump is a rugged device. If water doesn’t pump out, check to see the pump is turning freely; you can often tell by turning the motor shaft with long-nose pliers. If it’s binding, disassemble the pump and inspect for foreign objects. Motor bearings are usually accessible and will seldom require more  than cleaning and oiling if the motor shaft itself is binding.  A strainer, usually in the bottom of the tub, protects the dishwasher pump a compromise, however; its openings must be large enough to allow soft food deposits to pass and be flushed away, but small enough lo stop bits of bone, glass, olive pits, etc. The problem lies in small pieces of hard material. Check the strainer carefully whenever a foreign object is found in the pump. It’s a tough feeling when you reassemble the pump only to hear the “chunk” of another object logging against the impeller. If the dishwasher pump turns freely, check the pump motor for continuity with your volt meter.

Expert Tips for Stove, Range and Oven Repair in Brooklyn, NY

The information we provide on our website is here to help you gain more knowledge about your stove. More efficient stove usage can help you save on your utility bills and on possible future repairs by extending the life of your stove.

Warning: STOVES CAN BECOME DANGEROUS IF YOU TRY TO REPAIR WITHOUT EXPERIENCE, TRADE KNOWLEDGE, AND THE RIGHT TOOLS. We strongly advise you not perform any stove repairs on your own. Stove repairs attempted by anyone without professional experience, training, and understanding of gas and electrical systems can become very dangerous. For professional stove repair in Brooklyn, NY call Bear Appliance Repair 24 hours a day, 7 days a week.



By controlling the amount of gas which flows to a burner, the gas valve controls the heat output. The housing is threaded on the outlet end for an orifice or hood. The grill is adjustable with the hood turned completely in toward the body, if output is correct for LP gas. As it is turned in the opposite direction, it call hi, adjusted for natural gas. The setting of such surfaces should be checked with instruments for measuring the amount of gas flow to be sure that it complies with the nameplate rating.

On the opposite end of the body, threads hold a cap to retain the spring and pull, in place. A stem on the plug extends through the cap and is provided with the surface for the knob.

The manifold is filled with gas from the supply. A bottom extension of the valve threaded into the manifold.  At the burner there’s a small surface at the opening of the zip tube. When the gas is turned on, the gas-air mixture flows into the tube toward the pilot at the opposite end. Then the tube is ignited, the flame flows back to the burner, and the burner is ignited almost instantaneously. Many newer gas ranges incorporate an electronic capacitor charge ignition. This has a small printed circuit board which spark gaps or electrodes extend to the burners. When this swift is turned to the light position, arcing occurs at file spark and flip gas jet from the burner is ignited.

When this arrangement is used, is no pilot at the burner. Some ovens use this arrangement also use a glow coil for automatic lighting, and still others use a spark pilot. The advantage of the automatic ignition system is being consumed when the appliance is not in use.  . Flame is usually the first indication of Tinting around the burner. Two thermostats may be employed on these models. One thermostat controls gas flow to the burner, increasing or decreasing the how to provide the correct heat input. The second thermostat controls system in the electric operational mode. At this time an electric heating element, rather than a gas burner, is acting as the heat source thermostat simply cycles this heater on and off as required. Check this procedure for the electric thermostat is the same as for thermo falls on electric refrigerators.


There are two new developments in the home cooking field that we can expect to be around for a long time. The ceramic cooktop has met with great approval from housewives because of its appearance and the ease with which it can be cleaned. Elements for these units are located under the pattern for the pan, and are serviced by raising the top. Use extreme care when working around the fragile material dropped wrench or a slip of the hand can result in a chipped or cracked cooktop. Some ceramic tops use switches with sensing bulbs much like those used to control the oven. Be sure that they are repositioned exactly before securing the top in place

For professional help call Bear Appliance Repair in Brooklyn, NY 24/7.

Dryer Switch Repair Tips

Bear Appliance Repair works on all brands of electric and gas dryers in Brooklyn. If your dryer doesn’t produce heat, drum doesn’t turn or if you have any other problem, simply call our toll free number and let us fix the problem and return your dryer to perfect working order. Call them today to schedule an appointment for your dryer repair. Theywill work with you to set up a repair appointment for a time that is most convenient for you:

When scheduling a dryer repair appointment, Bear Appliance Repair in Brooklyn, NY always accommodates your busy life style.

The information we provide on our website is here to help you gain more knowledge about your dryer. More efficient dryer usage can help you save on your utility bills and on possible future repairs by extending the life of your dryer.
Warning: DRYERS CAN BECOME DANGEROUS IF YOU TRY TO REPAIR WITHOUT EXPERIENCE, TRADE KNOWLEDGE, AND THE RIGHT TOOLS. We strongly advise you not perform any dryer repairs on your own. Dryer repairs attempted by anyone without professional experience, training, and understanding of gas and electrical systems can become very dangerous. For professional help call our dryer repair technicians 24 hours a day, 7 days a week.


The motor centrifugal switch serves a dual purpose in clothes dryer. It does the job of a centrifugal switch in a split-phase motor when it opens the circuit to the starting winding as the motor approaches full speed. In the dryer, an additional set of contacts close the circuit to the heat source when top speed is reached. There are two reasons for the additional circuit. First, most dryers use heating elements rated at 5600 watts or so (about 24.5 amperes). Add to this the motor-starting current and a 30-ampere fuse or circuit breaker doesn’t stand a chance. With the centrifugal switch turning the element on after the starting windings are removed from the circuit, however, you are well within the limits of a 30-ampere circuit. There’s a built-in safety advantage here, also. If the motor fails to start for any reason, the heat source will not be energized. The push-to-start switch is an innovation that has come into wide usage in recent years. It’s a safety feature, requiring the push of a button to start the dryer at the beginning of the cycle or after interrupting the cycle by opening the door. It works like this: Depressing the push-to-start switch completes a circuit to the motor through a set of contacts in the motor’s centrifugal switch. As the motor reaches full speed, these contacts transfer to others that energize the motor directly from the timer. This action, occurring instantaneously, takes the push-to-start switch out of the circuit and acts as a holding circuit to keep the motor in operation. Many electric dryers use relays, energized by the timer contacts, to control the heating element

For professional dryer repair help call Bear Appliance Repair 24/7.

Power-Saving Efficiency Tips for Your Appliances


For less than 840 you can buy a plug-in microcontroller that lets an appliance with an induction motor such as a refrigerator, freezer, window air conditioner, or furnace fan, run cooler and ignore quietly on less electricity. This microcontroller, called the Energy Smart Power Planner and manufactured, CEM Industries, is intended for older appliances; newer ones often have a microcontroller built in. The device comes in 8-, 10-, and 20-amp models to handle almost any household appliance that has an induction motor


Control refrigerator prevent odors from spreading, make sure all food is wrapped, covered, or bagged in plastic. The only exception is the fruits and vegetables stored in crisper drawers. And in a frost-free, bag those too otherwise they’ll dry out. Before refrigerating any liquid, put it in a tightly sealed container. Moisture that evaporates inside a refrigerator just makes the unit work harder. To cool food quickly before freezing (and to reduce energy costs) set hot pans in ice water. Wrap the food and freeze it at once. When stocking an empty freezer, add 3 pounds or less of unfrozen food per cubic foot of space each time until the freezer is full. This will allow the food to freeze quickly and thoroughly, retarding the growth of bacteria. Keep a freezer inventory list. It cuts the time you keep the freezer door open looking for food and helps you use older items first.


Knowing how many years you’re likely to keep an appliance helps you to compare models more accurately than if you base your purchasing decision on just the initial cost. With a major appliance, first find estimated yearly cost on the appliance’s energy guide label, then multiply that yearly cost by the appliance’s estimated life. Add the result to the purchase price and you will have a good approximation of the appliance’s true cost. If you don’t have the means of determining how long you will have an appliance you can always contact Bear Appliance Repair in Brooklyn, NY to assist you with any repair needs that may occur while living in the New York area.

Major Appliances
Clothes dryer (electric) – 20
Clothes dryer (gas) -22
Clothes washer – 24
Dishwasher – 16
Freezer – 22
Garbage disposer – 12
Microwave oven – 14
Range (gas) – 28
Refrigerator – 23
Trash compactor – 15
Broiler oven – 9

Small appliances
Blender – 8
Coffee maker (drip) – 3
Coffee maker (percolator) – 6
Food processor – 8
Iron – 9
Mixer – 9
Toaster – 8

For professional appliance repair help contact Bear Appliance Repair in Brooklyn, NY immediately.

Keeping Your Automatic Washer Troublefree

The best way that I have found to do is to make the diagnosis first from the symptoms of the machine, then from further tests in the areas where the particular problem is likely to occur. Symptoms are listed in the order they are most likely to incur in the cycle of the machine.

SYMPTOM: Water will not enter the machine

If your washer doesn’t spin, the agitator doesn’t turn, or if you have any other problem, simply contact a Brooklyn appliance repair specialist and let us them the problem and return your washer to perfect working order. Call them today to schedule an appointment for your washer repair in Brooklyn. They will work with you to set up a repair appointment for a time that is most convenient for you:

Check the obvious first: An inlet hose may be crimped, or perhaps is turned off. Water-inlet hoses have filter screens. Sand or rust scaled off within the water line may have clogged the screens. Another filter is located in the inlet valve at the point where the hose attaches to the machine. Remove these screens and clean them under a running faucet, using an old tooth brush to remove all of the accumulation. Often these won’t appear to be clogged yet they won’t pass water, due to thin transparent film of algae. If cleaning doesn’t remove all, replace the screens. Don’t operate the washer without screens, as particles might lodge in the valve and prevent it from closing. If no results use your ears for a moment. Is there a low buzzing sound when the water should be coming in If not, go to the water­ in valve. To get to this valve you must raise the top of the washer. Remove the screws, raise the top tilt the back, and slide it forward. Before exposing any electrical conneclions in this manner, always unplug the machine. Water inlet valves in automatic washers are operated by a solenoid. When current flows through this coil, a magnetic field is created, raising if plunger inside the valve and allowing water to flow into the machine. When the magnetic force is removed, spring action seats the plunger and the water flow is shut off.

Your washer will have one, two, or three of these solenoids, de­pending oil the number of water-temperature selections. To check the coils, look for the wires leading to the water valve. Each coil will have two wires connected to its terminals. Check the coils for continuity and ground with your meter. A deflection should occur when the meter leads are placed across the terminals of a solenoid, denoting electrical continuity through the coils of wire within. To check for a ground, touch one meter lead to the frame of the cabinet, the other to each of the solenoid terminals in turn. No meter deflection should occur, no electrical leakage to ground. If either test shows that the solenoids is faulty, remove the screws that connect it to the valve and replace it with a new one obtained from your dealer. If all checks well, refer to the wiring diagram on the machine for it component marked “water-level switch” or “float switch.” This switch controls the amount of water entering the basket. The diagram shows one of the wires from the switch leading from the timer, and another leading to the inlet-valve solenoid or to the water-temperature Continuity should be read across these two terminals, water in the basket, and with one of the wires disconnected at the Dash on terminals. Now go to the water-temperature switch, and check for continuity from the terminal from the water-level switch file terminal leading to the solenoid in question. Keep in mind the short cuts possible when you use one of the best test instruments available your own ears. Listen to the machine. If you hear a slight hum, the solenoid is buzzing. This tells you that the solenoid, water-level switch, timer, temperature switch, and other washer components are good. The problem is mechanical. Check for restriction in the water line. By the same token, should no hum be heard, eliminate the mechanical operation of the water-inlet valve and devote your time to testing the electrical components with your meter. Applying your efforts and thinking along this line makes your diagnosis more accurate and much quicker, and prevents traveling up many blind alleys. It’s as easy its 1, 2, 3. Observe, listen, and analyze accordingly

For professional help call us 24/7 at

Expert heating and furnace repair tips for at home repair men

The information we provide on our website is here to help you gain more knowledge about your Heating or Furnace system. More efficient Heating or Furnace system usage can help you save on your utility bills and on possible future repairs by extending the life of your Heating or Furnace system.

Warning: HEATING OR FURNACE SYSTEMS CAN BECOME DANGEROUS IF YOU TRY TO REPAIR WITHOUT EXPERIENCE, TRADE KNOWLEDGE, AND THE RIGHT TOOLS. We strongly advise you not perform any Heating or Furnace system repairs on your own. Heating or Furnace system repairs attempted by anyone without professional experience, training, and understanding of gas and electrical systems can become very dangerous. For professional help call Bear Appliance Repair in Brooklyn, NY 24 hours a day, 7 days a week.

When the furnace works but heat doesn’t get through

IF YOUR OIL BURNER or gas fur­nace is functioning, but heat is not being delivered to the rooms, there is a malfunction in the delivery system. Let’s run down each of the delivery systems to see what you can do to overcome the problem, and at least get some heat into the house.

Steam system—Check the boiler gauge. A burner will shut off automatically if the water level in the boiler gets below a certain level.
Hot-water system Inspect the circulator. One that needs lubrication will not circulate hot water although the burner will continue to operate. Caution: Lubricate the circulator only with the grade of oil and/or cup grease recommended on the instruc­tion plate attached to the circulator’s body. Any other type may cause a complete breakdown.
If the circulator has stopped work­ing whether for lack of lubricant or some other reason, press the reset button on the device one time only. If there is no reset button, slap the housing with your hand. A circulator will not deliver heat if one of its couplings is broken. How­ever, the unit will continue to run, so put your ear close to the housing and listen for a sharp, rapping sound.

You may be able to repair the break temporarily. Remove the access cover. If you can get at the broken coupling, wire the broken cross-pieces together. If you cannot repair the circulator, but the burner is operating, you should be able to get some heat through the house. Most hot-water systems have a flow valve on the water line that runs from the furnace to the heat-radiating components. Open the valve. This will feed hot water through the system by gravity.

Important: Don’t forget to close the flow valve after the circulator has been repaired.
Forced-air systems One reason for a reduced heat condition in a forced-air system is a clogged air fil­ter. If you have a spare around, install it. If not, remove the old filter (some furnaces have more than one), take it out-of-doors, and knock it against a hard surface to loosen dirt.

Another reason for little heat delivery is a broken blower-motor belt. The best solution is to replace the belt, so you should keep a spare on hand. You can buy a belt for your blower motor from a hardware store or gasoline station. Make sure it is the right size. Place the belt on the blower-motor pulleys and tighten the adjusting nut, which is usually found behind the motor, until the belt has about 1/2-inch free play. If you do not have a spare belt, try wrapping some strong rope around the pulleys as a temporary measure. A final reason for failure of a forced-air system to deliver heat is a short in the blower motor. A short is indicated by on-off cycling of the motor in short spurts or complete refusal to run. Shut off the switch controlling the blower motor and remove all filters from the furnace. Some hot air will rise and permeate through the ducts to the registers so that minimum fort may be attained until a service technician arrives.

For professional help call Bear Appliance Repair 24/7:

Bear Appliance Repair repairs all models and brands of Heating or Furnace systems in Brooklyn. If your Heating or Furnace system is noisy, you feel smell of gas or if you have any other problem, simply call their toll free number and let them fix the problem and return your Heating or Furnace system to perfect working order. Call them today to schedule an appointment for your Heating or Furnace system repair in Brooklyn. They will work with you to set up a repair appointment for a time that is most convenient for you.